Double Head Waterjet Cutting Machine
- Pump:A50+B
- Cutting Table: YF-3020BA
- Cutting Head: Double head,3 Axis
- Auto abrasive delivery system;
- PC Based CNC Controller;
- One set of tool and spare parts kits
Specifications
| A50+B PUMP | ||
| Main Motor Power | 37kW(50HP) |  |
| Max Pressure | 420Mpa | |
| Max Water Discharge | 3.8L/min | |
| Max available Orifice Diameter | 0.33mm | |
| Pressure Transfer Ratio | 1:21 | |
| Oil tank capacity | 120L | |
| Power supply | 220V/60Hz/3PH | |
| Length/width/height | 1710/1500/1191 | |
| Weight | 1060kg | |
| Main Parts | Brand | Reference picture |
| Intensifier | WATERJET |
|
| Motor | Siemens/Innomotics（BEIDE） | |
| Hydraulic Pump | WATERJET | |
| PLC | OMRON | |
| Heat Exchanger | Air cooling | |
| Control System | LP/HP auto control | |
| Temperature Display | Digital temperature display | |
| Directional Valve | WATERJET | |
| Accumulator Volume | 1.0L | |
| Low Pressure Filter | 10μ | |
| Water Supply | 1/2″ | |
| Water Pressure | 0.3Mpa | |
| Water Drain | 3/8″ | |
| Pipeline Connection | HP 3/8″ M20 x 1.5 | |
| Compressed Air Pressure | 0.6Mpa | |
| Connection for Hose | 6mm | |
| Function | Description | |
| Air Cooling | Has good cooling effect. | |
| Overtemperature Alarm | An electronic temperature control meter is used to monitor the oil temperature and give an over-temperature alarm to avoid equipment problems caused by over-high oil temperature. | |
| Multistage Filtration | Four-stage water filtering device is adopted to avoid water quality problems and prolong the service life of equipment. | |
Cutting Table
 | Structural style | Bridge |
| X and Y axis Travel | 3000*2000mm | |
| Z-axis Travel | 150mm | |
| Control accuracy | ±0.01mm | |
| Cutting accuracy | ±0.2mm | |
| X/Y-axis Max. moving speed | 8000mm/min | |
| Z-axis Max. moving speed | 1000mm/min | |
 | Cutting Head | Double head,3 Axis |
| Way of Drive | AC Servo | |
| Servo System | INOVANCE | |
| Ball Screw | TBI | |
| Atmosphere Pressure | 86Kpa~106Kpa | |
 | Dust Concentration | Not More than 10mg/m3 |
| X Axis Structure | Aluminium/Steel Structure | |
| Water Tank | Coated Stainless Steel |
3 Axis Cutting Head
| Special CNC System |  |
| 3 Axis Linkage Cutting | |
| Multiple Heads are Available | |
| Less Parameter,more stable |
Main Characteristics of CNC System
| Industrial PC |  |
| 18.5 Inch LCD Monitor | |
| Weihong NcStudio | |
| Support DXF and NC code file | |
| Forward and backward processing function | |
| Even pace control function | |
| Partial and smooth processing modes | |
| Small arcs speed auto processing function | |
| Circle processing function | |
| Coordinate memory retention function | |
| Set delay time free | |
| Pause, continue and processing from any division function | |
Auto Abrasive Delivery System
| Max. Inlet Air Pressure | 0.3Mpa |  |
| Min. Inlet Air Pressure | 0.2Mpa | |
| Abrasive Capacity | 150Kg | |
| Min. Inlet Air Flow | 0.028 m3/min | |
| Operating Air Flow | 0.005 m3/min | |
| Self-feeding Control | ||
| Air Valve to prevent jams and breakages | ||
| Self sealing | ||
Equipment Installation Conditions
| Installation Position | 1.Indoor, with a net height of not less than 4.5m. |
| 2.Temperature: 5 – 40 ℃ | |
| 3.Maximum relative humidity: 95 % | |
| Water source requirements | Pressure> 0.3Mpa, soft water |
| Power requirements: | three – phase, 220V，AC,60hz, 100A, voltage fluctuation within 5 % |
| Air source requirements | compressed air supply pressure: > 0.6 Mpa compressed air supply flow: > 28.3 l / min |
| Oil Requirements | need 120L, antiwear hydraulic oil(46#); |
| Abrasive Requirements | sand, size 60 – 100 mesh, consumption: 15 – 45 kg / h |
Tool kit and Spare Parts Kit for A50
| Tool Kits List | |||
| Name | Model | Qty（pcs/sets） | Application |
| Tools for plunger seal | YF-T-001 | 1 | Plunger seal maintenance |
| Tool for HP cylinder | YF-T-002 | 1 | HP cylinder maintenance |
| Tools for on/off body | YF-T-003 | 1 | For on/off valve |
| Tools for end cap | YF-T-004 | 1 | end cap maintenance |
| Air duster | YF-T-005 | 1 | Cleaning |
| Spare parts list | |||
| Nozzle | YF-1227-1-40 | 2 | Used for cutting head body |
| Orifice | Import 0.22 | 4 | Used for cutting head body |
| On/Off Valve Seal | New C type | 2 | Used for cutting head body |
| Ceramic Insert | PEI12030 | 2 | Used for intensifier |
| Poppet | 12030 | 2 | Used for intensifier |
| White goop | Import | 1 | Used for anti-seizure of the threads |
| O-ring | 30×3.1 | 2 | Used for oil circuit |
| O-ring | 40×3.1 | 2 | Used for oil circuit |
| O-ring | 9.5×1.8 | 2 | Used for oil circuit |
| O-ring | 33.5×2.65 | 4 | Used for oil circuit |
| O-ring | 8×1.9 | 2 | Used for oil circuit |
| Back-up ring | 06A-01-05 | 2 | Used for oil circuit |
| Combined seal washer | Φ33 JB982-77 | 2 | Used for oil circuit |
| Combined seal washer | Φ42 JB982-77 | 2 | Used for oil circuit |
| Rubber band | N/A | 20m | Used for guard |